ISI Papers With Our Products

Title: Using Electrospinning Technique for Preparation of Cobalt Hydroxide Nanoparticles
Journal: Qatar Foundation Annual Research Conference Proceedings
Author: 1. Mohammad Madani, 2. Abdelmagid Salem Hamouda
Year: 2016
Address: 1. Department Nanotechnology, Agricultural Biotechnology Research Institute of Iran (ABRII), AREEO, 3135933151 Karaj, Iran, IR 2. Department of Mechanical and Industrial Engineering, Qatar University, Doha, Qatar, QA
Abstract: Cobalt hydroxide or cobaltous hydroxide or cobaltous hydrate, has attracted increasing attention in recent years because of its novel electric and catalytic properties and important technological applications, for examples in advanced batteries, supercapacitors, solar cells, electrochromics, as an oil additive, it can improve tribological properties [1,2], etc. Cobalt hydroxide nanoparticles were prepared via in-situ electrospinning. Thus, electrospinning of polyethylene oxide solution with different cobalt nitrate concentrations were carried out in gaseous ammonia atmosphere. The reaction of cobalt nitrate with ammonia produces cobalt hydroxide. The reaction occurs during fiber formation. Transmission Electron Microscopy (TEM) showed that cobalt hydroxide Co(OH)2 nanoparticles were formed on the produced nanofibers of 100-600 nm in diameter. The existence of the formed Co(OH)2 was also proven by X-ray Diffraction (XRD) analysis and it showed that the Co(OH)2 nanoparticles were produced. Thermogravimetric Analysis (TGA) results also confirmed the presence of Co(OH)2 within the fibers. Experimental Section Co(NO3)2.6H2O (supplied by Merck Chemical Co.) with different concentrations was dissolved in 100 mL distilled water to produced Co+2 solution. Then, the following seven experiments (Exp. G1, G2, G3, G4, G5 (collectively called G-series in this article), P, and N) were carried out. G-series: 4.0 g of polyethylene oxide (with weight average molecular weight of 600,000 g/mol and supplied by Acros Organics Co.) was added to 100 mL of above mentioned cobalt nitrate solution with different concentrations (given in Table Ι) and left for two nights to obtain a homogenous PEO solution having cobalt ions. The polymer solution was put into a hypodermic syringe. A syringe pump (Stoelting Co., USA) was used to feed the polymer solution into a metallic needle with an inner diameter of 0.7 mm. A grounded aluminum foil as collector was placed at a fixed distance of 18 cm from the needle. The metallic needle and the collector were enclosed in a polymethyl metacrylate box (40′50′60 cm). The feed rate of the syringe pump was fixed at 0.7 mL/h. A positive potential of 18 kV was then applied to the polymer solution using a high-voltage power supplier (HV35P series, Fnm Co., IR) with a maximum voltage of 35 kV. During electrospinning, gaseous ammonia (from a cylinder purchased from Merck Chemical) was purged into the box with a rate of 10 L/min. Electrospun nanofibers were collected on the surface of the grounded aluminum foil. Results and Discussion A comparison of the appearance (color change) of the mats obtained from G-series with that of the P fiber mat suggested that the cobalt ions in the jet traveling the distance between the needle and the collector could precipitate in the gaseous ammonia atmosphere to produce cobalt hydroxide. In other words, in this process, one reaction occurs during fiber formation: the reaction of Co+2 ions with NH3 which produces Co(OH)2 nanoparticles on the nanofibers. Cobalt (II) hydroxide is obtained as a precipitate when an alkaline hydroxide is added to an aqueous solution of cobalt (II) salt. Since the reaction of nanoparticle formations occurs during fiber formation in electrospinning process, the precipitated nanoparticles have special morphology and crystalline structures (due to the applied voltage, elongation, etc.).
Application: Nanoparticles
Product Model 1: High Voltage Power Supply (HV35P)
Product Model 2:
URL:"" & "/doi/abs/10.5339/qfarc.2016.EEPP1129"#